to access the security code what buttons do you press to get the code have little issue with the machine boggs down abit when using to fuctions at the same time or if you go to move it and press the pedals half way it boggs some what if you push them all the way it dosn't do it.Thanks
Product: EXCAVATOR Model: 325B L EXCAVATOR 2JR Configuration: 325B L Excavator 2JR00001-UP (MACHINE) POWERED BY 3116 Engine Testing and Adjusting 308B, 311B, 312B, 315B, 317B, 318B, 320B, 322B, 325B, 330B, M325B and W330B Excavators Engine and Pump Control Media Number -RENR1998-06 Publication Date -01/10/2004 Date Updated -06/10/2004 i01768419 Using Service Mode SMCS - 7569 Illustration 1 g00904377 Monitor Panel (1) Action lamp (2) Character display (3) Fuel gauge (4) Hydraulic oil temperature gauge (5) Engine coolant temperature gauge (6) Charge alert indicator (7) Alert indicator for the engine oil pressure (8) Alert indicator for the hydraulic oil temperature (9) Alert indicator for the engine coolant temperature (10) Clogged air filter indicator (11) Indicator for a hydraulic return filter that is clogged (12) Controller alert indicator (13) Monitor alert indicator (14) Air heater indicator (15) Fuel level alert (16) Hydraulic oil level alert (17) Engine oil level alert (18) Alert indicator for the engine coolant level (19) Power mode switch (20) AEC switch (21) Travel speed control switch (22) Travel alarm cancel switch (23) Boom priority mode switch (24) Swing priority mode switch (25) Fine control mode switch (26) User mode switch (27) Pictograph symbol The Electronic Monitor Panel will activate. Then, the monitor will display the output that is received from the controller. The Controller Service Program is divided into five functions. Each function is listed: Alerting the presence of abnormal engine operation Displaying the machine conditions (engine speed, hydraulic oil temperature, power shift pressure, etc) Service codes: 10 to 21. Displaying the existing electronic problems or the past electronic problems Service codes: 18, 19, 1c, 1d The electronic control components are adjusted and tested. The adjustment codes are listed: 70 and 71. The test codes are listed: 60, 61, 62, 66 and 67. Changes in various defaults in the controller Service codes: 80 to 8A You should depress the switches on the monitor panel in order to start up the service program or the switches are depressed in order to change the functions. The corresponding switch and/or switches should be depressed until the required function is displayed on the character display. Start-Up Of The Service Mode Illustration 2 g00662936 Electronic Monitor Panel (2) Character display (22) Travel alarm cancel switch (23) Boom priority mode switch (24) Swing priority mode switch (25) Fine control mode switch (26) User mode switch Note: The engine can be running or the engine can be stopped, when the "Service Mode" is started. When the engine is stopped, the starter switch must be in the ON position. You should know the procedure to start up the "Service Mode" in advance. The following switches should be depressed and held for 2 seconds or more simultaneously: travel alarm cancel switch (22), fine control mode switch (25) and user mode switch (26) . The time display and the dial display on the character display (2) will change to a "0" and a "0". The left character position will flash. You need to enter the following security code: OE 32 3A. Note: The security code must be entered within 10 seconds after the first procedure (1). Otherwise, the time display will return. You should learn the procedure of entering the security code in advance. The procedure to input information is listed: The figure that is blinking on the character display (2) can be changed. In order to change the figure, you should depress the boom priority mode switch (23) or the swing priority mode switch (24). The figure that is blinking increases (Boom priority mode switch (23) ) The figure that is blinking decreases (Swing priority mode switch (24) ) The character position that is blinking can be shifted by depressing the fine control mode switch (25) or the user mode switch (26). The character position that is blinking shifts to the right (Fine control mode switch (25) ). The character position that is blinking shifts to the left (User mode switch (26) ). After you enter the security code, the service mode is activated by depressing and holding the following switches for 2 seconds or greater: travel alarm cancel switch (22), fine control mode switch (25) and user mode switch (26). The service mode is automatically activated 10 seconds after the security code is entered. Now, the "Service Mode" is activated and the character display (2) will display "10" on the left two character positions and "1" on the right character position. Changing The Service Mode The boom priority mode switch (23) or the swing priority mode switch (24) is pressed in order to change the figures that are blinking on character display (2) . The figure that is blinking increases (Boom priority mode switch (23) ) The figure that is blinking decreases (Swing priority mode switch (24) ) The position that is blinking on the character display (2) can be shifted by depressing the fine control mode switch (25) and the user mode switch (26) . The position that is blinking shifts to the right (Fine control mode switch (25) ) The position that is blinking shifts to the left (Swing priority mode switch (24) ) Note: Refer to the chart of Service Codes for selecting the functions for the "Service Mode". Table 1 Service Code Function 10 Automatic Travel Speed Change 11 Low Temperature Control 12 Engine Speed 13 Engine Coolant Temperature 14 Hydraulic Oil Temperature 16 Digital Input 17 Software Version 18 Real Time Error Code 19 Error Log 1a Engine Speed Dial Setting Check 1b Model Name and Engine Type 1c Real Time Error Code (ATT) 1d Error Log (ATT) 20 Power Shift Pressure Command Signal 21 Displays Higher Delivery Pressure Of Main Pumps 60 Proportional Reducing Valve Sweep Test 61 Governor Actuator Sweep Test 62 ON/OFF Test Of Digital Output 66 Fixed Power Shift Pressure 67 Engine Speed Change 70 Governor Actuator Calibration 71 Proportional Reducing Valve Calibration 80 Setting Of Hydraulic Oil Type Mineral Or Biological 81 Setting Of AEC Speed 82 Setting Of AEC Delay Time 83 Setting Of Memory Mode 84 Setting Of Reduced Horsepower For Attachment Pump 85 Setting Of Engine Speed For Low Idle Switch 86 Setting Of Pump Quantity For Hammer Mode 87 Setting Of Hammer Circuit Pressure 88 Setting Of Pump Flow For Hammer Mode 8a Setting Of Power Offset For Attachment Pump 8b Change Of Preset Conditions Of Main Pump Output 8c Change Of Upper Limits Of Preset Conditions Of Main Pump Output (Such As Power Mode Or Engine Speed At Dial Position 10) Procedure To Stop The Service Mode Note: One of the following two methods should be used. Turn the starter switch to the OFF position. The following switches should be depressed and held simultaneously for 2 second or more: (22) Travel alarm cancel switch (25) Fine control mode switch (26) User mode switch The service mode has been stopped, if the character display shows the position of the engine speed dial on the right two character positions and the time is shown on the left four character positions.