Hi! This is a 2010 Terex TA400 with SN: A9821095. The problem is a bit confusing, would anyone have an idea what could be causing this: Let's say the vehicle is parked. The driver can start it, and shift from park to 1st. The shifter moves, and the driver can move forward. However, the truck will not shift into a higher gear. If the driver stops and shifts into reverse, the truck will still move forward in 1st. After shutting off and restarting the truck, if you move the shifter to reverse, the truck will move backwards. If you then stop and move the shifter to 1, the truck will continue in reverse. Any ideas? Thanks, Rildin.
What are your fault codes? The transmission is staying in the last successful gear that it was in. This could be due to a number of faults, possibly a faulty speed sensor. Need some fault codes to make a informed suggestion.
Sorry for the long delay in replying, I had a short hospital stay. Since then, I went out to the site and checked the truck. I have not much experience with these trucks, but I do have some mechanic and electronic technician experience. I checked the fuses and relays, and had another delay while I waited for delivery of the relays. I changed 3 fuses, and found that about 3/4 of the relays tested bad. So I replaced all of the relays. I originally had several engine codes, and I think 3 transmission codes. After clearing the transmission codes, only one came back. I also did a test drive so I could have a first-hand description of the symptoms. The symptoms I experienced were: Truck started well, warmed up normally. Parking brake disengaged as expected. I placed the stick into the "D" position and drove forward. It drove normally, but would not shift. As the truck was given more fuel, the speed increased somewhat, as did the rpms, but it did not shift. I changed manually to gears in sequence, looking for a shift. It finally shifted to a different gear when the stick was in "4." At that point, after "feeling" the shift, the rpms went back down, but the speed increase was minimal. I stopped, the brakes worked normally. At this point in the test drive, the gear was "stuck." The stick was placed back in "D" and the truck went forward. In "N" it also went forward, and in "R" it also went only forward. We had to turn the truck off, restart it, and it was no longer stuck in gear, but it still wouldn't shift. There is only one transmission code showing, which is: P2714. Any help is appreciated. Thanks, Rildin.
Bump... hoping someone can help.
Code is P2714 Pressure Control Solenoid 4 (PCS4) Stuck Off see attached manual
Thanks for the replies! So, if PCS4's error message is that it's "stuck closed," is it just a matter of replacing that solenoid? Or, is it possible that the system is not getting some other signal that it is looking for, from something that PCS4 should be doing, and the system therefore thinks PCS4 is not doing "it's job?"
This may be a bit of a long shot, but its a relatively quick check. Did your issue just happen one day? Is the range light flashing? The computers would get all mixed up if the operator changed the range selector switch with the machine off. (ie, if the truck was shut off in low range, and then the high range was selected with the truck off, then truck was started) The truck would get stuck in a gear, and not shift. Just play with the range selector, and turn the key on and off. Usually just have to change the range selector with the key off.
C1312 Retarder Request Sensor Failed Low C1313 Retarder Request Sensor Failed High P0122 Pedal Position Sensor Circuit Low Voltage P0123 Pedal Position Sensor Circuit High Voltage P0218 Transmission Fluid Over temperature P0561 System Voltage Low Performance P0562 System Voltage Low P0563 System Voltage High P0602 TCM Not Programmed P0610 TCM Vehicle Options Error (Trans ID) P0613 TCM Processor P0614 Torque Control Mismatch (ECM/ TCM) P0634 TCM Internal Temperature Too High P063E Auto Configuration Throttle Input Not Present P063F Auto Configuration Engine Coolant Temperature Input Not Present P0658 Actuator Supply Voltage 1 Low (HSD 1 open/gnd) P0659 Actuator Supply Voltage 1 High (HSD 1 batt) P0701 Transmission Control System Performance P0702 Transmission Control System Electrical (Trans ID) P0703 Brake Switch Circuit P0708 Transmission Range Sensor Circuit - High Input P070C Transmission Fluid Level Sensor Circuit - Low Input P070D Transmission Fluid Level Sensor Circuit - High Input P0711 Transmission Fluid Temp. Sensor Circuit Performance P0712 Transmission Fluid Temperature Sensor Circuit Low Input P0713 Transmission Fluid Temperature Sensor Circuit High Input P0716 Turbine Speed Sensor Circuit Performance P0717 Turbine Speed Sensor Circuit No Signal P071D General Purpose Input Fault P071A RELS Input Failed On P0720 Output Speed Sensor Circuit P0721 Output Speed Sensor Circuit Performance P0722 Output Speed Sensor Circuit No Signal P0726 Engine Speed Input Circuit Performance P0727 Engine Speed Input Circuit No Signal P0729 Incorrect 6th Gear Ratio P0730 Incorrect Gear Ratio P0731 Incorrect 1st Gear Ratio P0732 Incorrect 2nd Gear Ratio P0733 Incorrect 3rd Gear Ratio P0734 Incorrect 4th Gear Ratio P0735 Incorrect 5th Gear Ratio P0736 Incorrect Reverse Ratio P0741 Torque Convertor Clutch System Stuck Off P0776 Pressure Control Solenoid 2 Controlled Clutch Stuck Off P0777 Pressure Control Solenoid 2 Controlled Clutch Stuck On
P0796 Pressure Control Solenoid 3 Controlled Clutch Stuck Off P0797 Pressure Control Solenoid 3 Controlled Clutch Stuck On P0842 Transmission Pressure Switch Solenoid 1 Circuit Low P0843 Transmission Pressure Switch Solenoid 1 Circuit High P0880 TCM Power Input Signal P0881 TCM Power Input Signal Performance (Battery Voltage) P0882 TCM Power Input Signal Low (Battery Voltage) P0883 TCM Power Input Signal High (Battery Voltage) P0960 Main Pressure Modulation Solenoid Control Circuit Open P0961 Main Pressure Modulation Solenoid System Performance P0962 Main Pressure Modulation Solenoid Control Circuit Low P0963 Main Pressure Modulation Solenoid Control Circuit High P0964 Pressure Control (PC) Solenoid 2 Control Circuit Open P0965 Pressure Control (PC) Solenoid 2 System Performance P0966 Pressure Control (PC) Solenoid 2 Control Circuit Low P0967 Pressure Control (PC) Solenoid 2 Control Circuit High P0968 Pressure Control (PC) Solenoid 3 Control Circuit Open P0969 Pressure Control (PC) Solenoid 3 System Performance P0970 Pressure Control (PC) Solenoid 3 Control Circuit Low P0971 Pressure Control (PC) Solenoid 3 Control Circuit High P0972 Shift Solenoid (SS) 1 Control Circuit Open P0973 Shift Solenoid (SS) 1 Control Circuit Low P0974 Shift Solenoid (SS) 1 Control Circuit High P0975 Shift Solenoid (SS) 2 Control Circuit Open P0976 Shift Solenoid (SS) 2 Control Circuit Low P0977 Shift Solenoid (SS) Control Circuit High P0989 Retarder Pressure Sensor Failed Low P0990 Retarder Pressure Sensor Failed High P1739 Incorrect Low Gear Ratio P1891 Throttle Position Sensor PWM Signal Low Input P1892 Throttle Position Sensor PWM Signal High Input P2184 Engine Coolant Temperature Sensor 2 Circuit Low P2185 Engine Coolant Temperature Sensor 2 Circuit High P2637 Torque Management Feedback Signal (SEM) P2641 Torque Management Feedback Signal (LRTP) P2670 Actuator Supply Voltage 2 Low (HSD 2 gnd) P2671 Actuator Supply Voltage 2 High (HSD 2 batt/open) P2685 Actuator Supply Voltage 3 Low (HSD 2 gnd) P2686 Actuator Supply Voltage 3 High (HSD 3 batt/open) P2714 Pressure Control Solenoid 4 Controlled Clutch Stuck Off P2715 Pressure Control Solenoid 4 Controlled Clutch Stuck On P2718 Pressure Control (PC) Solenoid 4 System Open P2719 Pressure Control (PC) Solenoid 4 System Performance P2720 Pressure Control (PC) Solenoid 4 Control Circuit Low P2721 Pressure Control (PC) Solenoid 4 Control Circuit High P2723 Pressure Control Solenoid 1 Controlled Clutch Stuck Off
P2724 Pressure Control Solenoid 1 Controlled Clutch Stuck On P2727 Pressure Control (PC) Solenoid 1 System Open P2728 Pressure Control (PC) Solenoid 1 System Performance P2729 Pressure Control (PC) Solenoid 1 Control Circuit Low P2730 Pressure Control (PC) Solenoid 1 Control Circuit High P2736 Pressure Control (PC) Solenoid 5 System Open P2737 Pressure Control (PC) Solenoid 5 System Performance P2738 Pressure Control (PC) Solenoid 5 Control Circuit Low P2739 Pressure Control (PC) Solenoid 5 Control Circuit High P2740 Retarder Oil Temperature Hot P2742 Retarder Oil Temperature Sensor Circuit - Low Input P2743 Retarder Oil Temperature Sensor Circuit - High Input P2761 TCC PCS Control Circuit Open P2762 TCC PCS Control Circuit Range/ Performance P2763 TCC PCS Control Ciruit High P2764 TCC PCS Control Circuit Low P278A Kickdown Input Switch Circuit P2793 Gear Shift Direction Circuit P2808 Pressure Control Solenoid 6 Controlled Clutch Stuck Off P2809 Pressure Control Solenoid 6 Controlled Clutch Stuck On P2812 Pressure Control (PC) Solenoid 6 System Open P2813 Pressure Control (PC) Solenoid 6 System Performance P2814 Pressure Control (PC) Solenoid 6 Control Circuit Low P2815 Pressure Control (PC) Solenoid 6 Control Circuit High U0001 Hi Speed CAN Bus Reset Counter Overrun (CAN2/IES CAN) U0010 CAN Bus Reset Counter Overrun (CAN1/J1939) U0100 Lost Communication with ECM / PCM "A" U0073 CAN Bus Reset Counter Overrun (CAN2/GMLAN) U0103 Lost Communication With Gear Shift Module 1 U0115 Lost Communication with ECM / PCM "B" U0291 Lost Communication with Gear Shift Module 2 U0292 Invalid Data received from Gear Shift Control Module 2 U0304 Software Incompatibility With Gear Shift Control Module 1 U0333 Software Incompatibility With Gear Shift Control Module 2 U0404 Invalid Data received from Gear Shift Control Module 1 U0592 Invalid Data received from Gear Shift Control Module 2
You could remove and inspect the cartridge, although you will likely not see anything wrong, even if it has failed. I believe that you can switch it with PCS3. It may not fix your problem, but something different should happen for testing purposes. You can verify the valve operation by monitoring the test ports. Gears 2 and 6 should have pressure at C4, which is supplied by PCS4