bobcat

1. #1Jon Boy2016-11-25 23:20

   bobcat 763 Please I need help I have input on my panel screen it is a 763G bobcat.I have tryed a lot of stuff to fix it it don't start

2. #2deck602016-11-26 18:39

   if its a digital key-less one they have had issues with the pad and computer ebay has some manuals they are usually good http://www.ebay.com/itm/Bobcat-763-...987115?hash=item1c751e09ab:g:wVYAAOSwxg5X0cdu

3. #3deck602016-11-26 18:45

   a friend of mine has a 185 with the digital and I think he is on his 4th keypad

4. #4Jon Boy2016-11-26 19:57

   bobcat763 My panel is not keyless it has the key on the right side but the panel on the left side don't do anything dose not even light up and I can't even press the main button to get it to move

5. #5deck602016-11-26 21:40

   that's weird check the pannel sounds like it might have a bad connection or came unplugged does the fuel gauge work? and temp? will it start? also check your fuses

6. #6deck602016-11-26 21:50

   I have the service manual for a 773-g the electrical should be pretty close but that's on my other computer will look for it tomorrow

7. #7deck602016-11-27 10:31

   check fuse f4 the following will be directly from the manual Corroded or loose grounds can cause multiple service codes and/or abnormal symptoms. All dash lights flashing, buzzer going off, headlights and taillights flashing, could indicate a bad ground. The same symptoms could apply if the voltage is low, such as loose or corroded battery cables. If you observe these symptoms, check grounds and positive leads first. Press and hold LIGHTS Button (Item 1) for two seconds to view SERVICE CODES in the HOUR METER/CODE DISPLAY (Item 2) [Figure 60-80-1]. If more than one SERVICE CODE is present, the codes will scroll on the HOUR METER/CODE DISPLAY. 01-16 Air filter not connected 11-05 Seat bar sensor short to battery 01-17 Air filter plugged 11-06 Seat bar sensor short to ground 02-16 Hydraulic charge filter not connected 12-21 Front auxiliary PWM switch out of range high 02-17 Hydraulic charge filter plugged 12-22 Front auxiliary PWM switch out of range low 12-23 Front auxiliary PWM switch not in neutral 03-09 Battery voltage low 03-10 Battery voltage high 13-05 Fuel shut-off hold solenoid short to battery 03-11 Battery voltage extremely high 13-06 Fuel shot-off hold solenoid short to ground 03-14 Battery voltage extremely low 13-07 Fuel shut-off solenoid open circuit 03-22 Battery voltage out of range low 14-02 Fuel shut-off pull solenoid error ON 04-09 Engine oil pressure low 14-03 Fuel shut-off pull solenoid error OFF 04-14 Engine oil pressure extremely low 04-15 Engine oil pressure shutdown level 15-02 Traction lock pull solenoid error ON 04-21 Engine oil pressure out of range high 15-03 Traction lock pull solenoid error OFF 04-22 Engine oil pressure out of range low 16-05 Traction lock hold solenoid short to battery 05-09 Hydraulic charge pressure low 16-06 Traction lock hold solenoid short to ground 05-14 Hydraulic charge pressure extremely low 16-07 Traction lock hold solenoid open circuit 05-15 Hydraulic charge pressure shutdown level 05-21 Hydraulic charge pressure out of range high 17-05 Hydraulic lock valve solenoid short to battery 05-22 Hydraulic charge pressure of range low 17-06 Hydraulic lock valve solenoid short to ground 17-07 Hydraulic lock valve solenoid open circuit 06-10 Engine speed high 06-11 Engine speed extremely high 18-05 Spool Lock Solenoid short to battery 06-13 Engine speed no signal 18-06 Spool Lock Solenoid short to ground 06-15 Engine speed shutdown level 18-07 Spool Lock Solenoid open circuit 06-18 Engine speed out of range 19-02 Bucket position solenoid error ON 07-10 Hydraulic oil temperature high 19-03 Bucket position solenoid error OFF 07-11 Hydraulic oil temperature extremely high 07-15 Hydraulic oil temperature shutdown level 20-02 Two-speed solenoid error ON 07-21 Hydraulic oil temperature out of range high 20-03 Two-speed solenoid error OFF 07-22 Hydraulic oil temperature out of range low 21-02 Glow plug error ON 08-10 Engine coolant temperature high 21-03 Glow plug error OFF 08-11 Engine coolant temperature extremely high 08-15 Engine coolant temperature shutdown level 22-02 Starter error ON 08-21 Engine coolant temperature out of range high 22-03 Starter error OFF 08-22 Engine coolant temperature out of range low 23-02 Rear base solenoid error ON 09-09 Fuel level low 23-03 Rear base solenoid error OFF 09-21 Fuel level out of range high 09-22 Fuel level out of range low 24-02 Rear rod solenoid error ON 24-03 Rear rod solenoid error OFF 773 Bobcat Loader 60-80-3 Service Manual Service Codes (Cont’d)DIAGNOSTICS (CONT’D) Service Codes (Cont’d)DIAGNOSTICS (CONT’D) CODE CODE 25-02 Rear auxiliary relief solenoid error ON 32-61 Handle lock short to ground 25-03 Rear auxiliary relief solenoid error Off 32-62 Handle lock short to battery 32-63 Pedal lock short to ground 26-02 Front base solenoid error ON 32-64 Pedal lock short to battery 26-03 Front base solenoid error OFF 32-65 Sensor supply voltage out of range 32-66 Battery voltage out of range 27-02 Front rod solenoid error ON 32-67 Switch flipped while operating 27-03 Front rod solenoid error OFF 32-68 Lift handle information error 32-69 Control pattern switch flipped while operating 28-02 Diverter solenoid error ON 32-70 Right drive handle short to ground

8. #8deck602016-11-27 10:34

   28-03 Diverter solenoid error OFF 32-71 Right drive handle short to battery 29-02 High flow solenoid error ON 33-23 Main Controller (Bobcat Controller) not programmed 29-03 High flow solenoid error OFF 34-04 Deluxe panel no communication to Bobcat controller 30-28 Controller Memory failure 35-02 Two-speed fan error ON 31-28 Interrupted power failure 35-03 Two-speed fan error OFF 32-04 ACS not communicating with Bobcat Controller 36-48 ACD multiple controllers present 32-23 ACS Not calibrated 32-31 Tilt actuator fault 37-02 Two-speed secondary error ON 32-32 Tilt actuator wiring fault 37-03 Two-speed secondary error OFF 32-33 Tilt handle wiring fault 32-34 Tilt actuator not in neutral 32-35 Tilt handle/pedal not in neutral 32-36 Lift actuator fault 32-37 Lift actuator wiring fault 32-38 Lift handle wiring fault 32-39 Lift actuator not in neutral 32-40 Lift handle/pedal not in neutral 32-41 No communication 32-49 Lift actuator short to ground 32-50 Tilt actuator short to ground 32-51 Lift actuator short to battery 32-52 Tilt actuator short to battery 32-53 Lift handle/pedal short to ground 32-54 Tilt handle/pedal short to ground 32-55 Lift handle/pedal short to battery 32-56 Tilt handle/pedal short to battery 32-57 Lift actuator reduced performance 32-58 Tilt actuator reduced performance 32-59 Lift actuator wrong direction 32-60 Tilt actuator wrong direction CODE CODE 38-04 No communication from joystick controller 38-53 Left forward drive solenoid error OFF 38-05 Left joystick X axis not in neutral 38-54 Left reverse drive solenoid error OFF 38-06 Right joystick X axis not in neutral 38-55 Right forward drive solenoid error OFF 38-07 Left joystick Y as not in neutral 38-56 Right reverse drive solenoid error OFF 38-08 Right joystick Y axis not in neutral 38-57 Front right extend steering solenoid error OFF 38-09 Control pattern switch - Short to Battery or Ground 38-58 Front right retract steering solenoid error OFF 38-11 Lift actuator not in neutral 38-59 Front left extend steering solenoid error OFF 38-12 Tilt actuator not in neutral 38-60 Front left retract steering solenoid error OFF 38-13 Lift actuator fault 38-61 Rear right extend steering solenoid error OFF 38-14 Tilt actuator fault 38-62 Rear right retract steering solenoid error OFF 38-15 Right wheel speed fault 38-63 Rear left extend steering solenoid error OFF 38-16 Left wheel speed fault 38-64 Rear left retract steering solenoid error OFF 38-17 Tilt actuator reduced performance 38-65 Steering pressure solenoid error OFF 38-18 Lift actuator reduced performance 38-66 Back-up alarm error OFF 38-19 Left joystick X axis out of range high 38-67 No communication from Bobcat controller 38-20 Right joystick X axis out of range low 38-68 Wheel angles (alignment) not calibrated 38-21 Left joystick Y axis out of range high 38-69 Lift & tilt actuators not calibrated 38-22 Right joystick Y axis out of range high 38-70 Interrupted power 38-23 Front right steering sensor out of range high 38-71 Battery out of range 38-24 Front left steering sensor out of range high 38-72 Drive pump not calibrated 38-25 Rear right steering sensor out of range high 38-73 Steering mode / drive mode switch flipped while operating 38-26 Rear left steering sensor out of range high 38-74 Uncommanded right wheel speed error ON 38-27 Lift actuator out of range high 38-75 Uncommanded left wheel speed error ON 38-28 Tilt actuator out of range high 38-76 Undercurrent steer pressure solenoid 38-29 Left joystick X axis out of range low 38-77 Undercurrent front right extend steer solenoid 38-30 Right joystick X axis out of range low 38-78 Undercurrent front right retract steer solenoid 38-31 Left joystick Y axis out of range low 38-79 Undercurrent front left extend steer solenoid 38-32 Right joystick Y axis out of range low 38-80 Undercurrent front left retract steer solenoid 38-33 Front right steering sensor out of range low 38-81 Undercurrent rear right extend steer solenoid 38-34 Front left steering sensor out of range low 38-82 Undercurrent rear right retract steer solenoid 38-35 Rear right steering sensor out of range low 38-83 Undercurrent rear left extend steer solenoid 38-36 Rear left steering sensor out of range low 38-84 Undercurrent rear left retract steer solenoid 38-37 5 volt sensor supply 1 out of range low 38-85 5 Volt sensor supply 1 out of range high 38-38 5 volt sensor supply 2 out of range low 38-86 5 Volt sensor supply 2 out of range high 38-39 Lift actuator short to ground / out of range low 38-87 Front right wheel blocked (steering mechanical failure) 38-40 Tilt actuator short to ground / out of range low 38-88 Front left wheel blocked (steering mechanical failure) 38-41 Tilt actuator wrong direction 38-89 Rear right wheel blocked (steering mechanical failure) 38-42 Lift actuator wrong direction 38-90 Rear left steering error 38-43 Left forward drive solenoid error ON 38-91 Right speed sensor missing pulses 38-44 Left reverse drive solenoid error ON 38-92 Left speed sensor missing pulses 38-45 Right forward drive solenoid error ON 38-93 Unresponsive right speed sensor 38-46 Right reverse drive solenoid error ON 38-94 Unresponsive left speed sensor 38-47 Front right steering solenoid error ON 38-98 Controller in drive calibration mode 38-48 Front left steering solenoid error ON 38-99 Controller in wheel position calibration mode. 38-49 Rear right steering solenoid error ON 38-50 Rear left steering solenoid error ON 38-51 Steering pressure solenoid error ON 38-52 Back-up alarm error ON CODE CODE CODE CODE 39-04 Left joystick no communication to Bobcat controller 85-02 ACD output ‘F’ error ON 85-03 ACD output ‘F’ error OFF 773 Bobcat Loader 60-80-5 Service Manual 40-04 Right joystick no communication to Bobcat controller 86-02 ACD output ‘G’ error ON 44-02 Horn error ON 86-03 ACD output ‘G’ error OFF 44-03 Horn error OFF 87-02 ACD output ‘H’ error ON 45-02 Right blinker error ON 87-03 ACD output ‘H’ error OFF 45-03 Right blinker error OFF 90-02 Service tool output ‘C’ error ON 46-02 Left blinker error ON 90-03 Service tool output ‘C’ error OFF 46-03 Left blinker error OFF 91-02 Service tool output ‘D’ error ON 47-21 8 volt sensor supply out of range high 91-03 Service tool output ‘D’ error OFF 47-22 8 volt sensor supply out of range low 92-02 Service tool output ‘E’ error ON 48-02 Front light relay error ON 92-03 Service tool output ‘E’ error OFF 48-03 Front light relay error OFF 93-02 Service tool output ‘F’ error ON 49-02 Rear light relay error ON 93-03 Service tool output ‘F’ error OFF 49-03 Rear light relay error OFF 60-21 Rear auxiliary control out of range high 60-22 Rear auxiliary control out of range low 60-23 Rear auxiliary control not returning to neutral 64-02 Switched power relay error ON 64-03 Switched power relay error OFF 74-72 Bobcat controller in boot code 74-73 Left hand panel system RX error 80-02 ACD output ‘A’ error ON 80-03 ACD output ‘A’ error OFF 81-02 ACD output ‘B’ error ON 81-03 ACD output’ B’ error OFF 82-02 ACD output ‘C’ error ON 82-03 ACD output ‘C’ error OFF 83-02 ACD output ‘D’ error ON 83-03 ACD output ‘D’ error OFF 84-02 ACD output ‘E’ error ON 84-03 ACD output ‘E’ error OFF